An electronic speed control or ESC is an electronic circuit with the purpose to vary an electric motor's speed, its direction and possibly also to act as a dynamic brake. ESCs are often used aboard an electrically powered radio control model.
An ESC can be a stand-alone unit which plugs into the receiver's throttle control channel or incorporated into the receiver itself, as is the case in most toy-grade R/C vehicles. Some R/C manufacturers that install proprietary hobby-grade electronics in their entry-level vehicles, vessels or aircraft use onboard electronics that combine the two on a single circuit board.
Function
Regardless of the type used, an ESC interprets control information not as mechanical motion as would be the case of a servo, but rather in a way that varies the switching rate of a network of field effect transistors, or "FET's." The rapid switching of the transistors is what causes the motor itself to emit its characteristic high-pitched whine, especially noticeable at lower speeds. It also allows much smoother and more precise variation of motor speed in a far more efficient manner than the mechanical type with a resistive coil and moving arm once in common use.
Most modern ESCs incorporate a battery eliminator circuit (or BEC) to regulate voltage for the receiver, removing the need for receiver batteries. BECs are usually either linear or switched mode voltage regulators.
DC ESCs in the broader sense are PWM controllers for electric motors. The ESC generally accepts a nominal 50 Hz PWM servo input signal whose pulse width varies from 1 ms to 2 ms. When supplied with a 1 ms width pulse at 50 Hz, the ESC responds by turning off the DC motor attached to its output. A 1.5 ms pulse-width input signal results in a 50% duty cycle output signal that drives the motor at approximately half-speed. When presented with 2.0 ms input signal, the motor runs at full speed due to the 100% duty cycle (on constantly) output.
Brushless ESC
Brushless motors otherwise called as outrunners have become very popular with radio controlled airplane hobbyists because of their efficiency, power, longevity and light weight in comparison to traditional brushed motors also known as inrunner. However, brushless DC motor controllers are much more complicated than brushed motor controllers. They have to convert the DC from the battery into phased AC (usually three phase) in order to produce the changing magnetic field.
The correct phase varies with the motor rotation, which is to be taken into account by the ESC: Usually, back EMF from the motor is used to detect this rotation, but variations exist that use magnetic (Hall Effect) or optical detectors. Computer-programmable speed controls generally have user-specified options which allows setting low voltage cut-off limits, timing, acceleration, braking and direction of rotation. Reversing the motor's direction may also be accomplished by switching any two of the three leads from the ESC to the motor.
Classification
ESCs are normally rated according to maximum current, for example, 25 amperes or 25 A. Generally the higher the rating, the larger and heavier the ESC tends to be which is a factor when calculating mass and balance in airplanes. Many modern ESCs support nickel metal hydride and lithium ion polymer batteries with a range of input and cut-off voltages. The type of battery and number of cells connected is an important consideration when choosing a BEC, whether built into the controller or as a stand-alone unit. A higher number of cells connected will result in a reduced power rating and therefore a lower number of servos supported by an integrated BEC.
Applications
Cars
ESCs designed for sport use in cars generally have reversing capability; newer sport controls can have the reversing ability overridden so that it can be used in a race. Controls designed specifically for racing and even some sport controls have the added advantage of dynamic braking capability. Simply put, the ESC forces the motor to act as a generator by placing an electrical load across the armature. This in turn makes the armature harder to turn, thus slowing or stopping the model. Some controllers add the benefit of regenerative braking. This puts the voltage being generated by the motor back to work recharging the vehicle's drive batteries. On full-sized vehicles, regenerative braking is used in electric and hybrid golf cars and hybrid automobiles while dynamic braking is used in diesel-electric locomotives to help slow trains on long downgrades.
Helicopters
ESCs designed for radio-control helicopters do not require a braking feature (indeed, turning it on would likely result in the main rotor assembly being severely damaged by the rotor blades) nor do they require reverse direction. Many high-end helicopter ESCs do provide a "Governor mode" which fixes the motor RPM to a set speed, greatly aiding CCPM based flight.
Airplanes
ESCs designed for radio-control airplanes usually contain a few safety features. If the power coming from the battery is insufficient to continue running the electric motor the ESC will reduce or cut off power to the motor while allowing continued use of ailerons,rudder and elevator function. This allows the pilot to retain control of the plane to glide or fly on low power to safety.
Boats
ESCs designed for boats are by necessity waterproof. Also, many are water-cooled. Like cars, boats need braking and reverse capability.
See also
- Castle Creations
- Novak Electronics
- Radio controlled model
- Tekin
References
- ^ http:
DC Motor speed control
The international forum for control engineers, system integrators, and industrial automation professionals.
AN009 - Versatile DC Motor PWM Speed Controller
ESP Application Notes - AN009 - Versatile DC Motor PWM Speed Controller
QKits Electronic Kits
15A DC Motor Speed Control Module Power supply :12/24 VDC Load voltage : 12/24 VDC / 15A max Output : controlled DC motor by PWM ( Pulse With Modulation ) Range : 0 - 100
Control, DC Speed - DC Speed Controls - Motor Supplies - Motors ...
Control, DC Speed 4Z527: For constant or diminishing torque applications.
Brushless dc speed control - 2004-08-01 06:00:00 | Control Engineering
BX Series brushless dc speed control system now includes high output power models of 200 and 400 W. Motors come with quiet GFH gearheads or in a round shaft version.
Control, DC Speed, Dc Speed Control, Fused Control Dc Speed Control
Control, DC Speed, Dc Speed Control, Fused Control Dc Speed Control, Control Circuit DC Speed Control, DC Variable Speed Control, Chassis Control, DC Speed, Chassis Dc Speed ...
MX033 - DC PWM Motor Speed Controller 15 Amp - Assembled & Tested
This 15AMP PWM DC motor controller circuit can be used for generating hydrogen (Brown's gas), build your own fuel cell station. More common uses include controlling DC motors in ...
DC Drive,Motor Speed Controller,Thyristor Controlled DC Drive,DC Motor ...
Gayatri Control, Ahmedabad- Manufacturers and exporters of DC drive, motor speed controller, thyristor controlled DC drive, DC motor speed controller, thyristor drives ...
DC Motor Speed Control - Motor Control Consulting - Brushless DC Motor ...
Control Resources' custom electronic design and manufacturing group has provided DC motor speed control solutions for several OEM customers. Our motor control consultant engineers ...
DC Speed Controllers
DC Speed Controllers - Wide Selection of DC Speed Controllers. Low online prices for high quality DC Speed Controllers in stock with great customer support. Great for both low and ...