Composite materials (or composites for short) are engineered materials made from two or more constituent materials with significantly different physical or chemical properties which remain separate and distinct on a macroscopic level within the finished structure.
History
Wood is a natural composite of cellulose fibers in a matrix of lignin. The most primitive manmade composite materials were straw and mud combined to form bricks for building construction; the Biblical Book of Exodus speaks of the Israelites being oppressed by Pharaoh, by being forced to make bricks without straw being provided. The ancient brick-making process can still be seen on Egyptian tomb paintings in the Metropolitan Museum of Art. The most advanced examples perform routinely on spacecraft in demanding environments. The most visible applications pave our roadways in the form of either steel and aggregate reinforced portland cement or asphalt concrete. Those composites closest to our personal hygiene form our shower stalls and bath tubs made of fiberglass. Solid surface, imitation granite and cultured marble sinks and counter tops are widely used to enhance our living experiences.
Composites are made up of individual materials referred to as constituent materials. There are two categories of constituent materials: matrix and reinforcement. At least one portion of each type is required. The matrix material surrounds and supports the reinforcement materials by maintaining their relative positions. The reinforcements impart their special mechanical and physical properties to enhance the matrix properties. A synergism produces material properties unavailable from the individual constituent materials, while the wide variety of matrix and strengthening materials allows the designer of the product or structure to choose an optimum combination.
Engineered composite materials must be formed to shape. The matrix material can be introduced to the reinforcement before or after the reinforcement material is placed into the mold cavity or onto the mold surface. The matrix material experiences a melding event, after which the part shape is essentially set. Depending upon the nature of the matrix material, this melding event can occur in various ways such as chemical polymerization or solidification from the melted state.
A variety of molding methods can be used according to the end-item design requirements. The principal factors impacting the methodology are the natures of the chosen matrix and reinforcement materials. Another important factor is the gross quantity of material to be produced. Large quantities can be used to justify high capital expenditures for rapid and automated manufacturing technology. Small production quantities are accommodated with lower capital expenditures but higher labor and tooling costs at a correspondingly slower rate.
Most commercially produced composites use a polymer matrix material often called a resin solution. There are many different polymers available depending upon the starting raw ingredients. There are several broad categories, each with numerous variations. The most common are known as polyester, vinyl ester, epoxy, phenolic, polyimide, polyamide, polypropylene, PEEK, and others. The reinforcement materials are often fibers but also commonly ground minerals. The various methods described below have been developed to reduce the resin content of the final product, or the fibre content is increased. As a rule of thumb, lay up results in a product containing 60% resin and 40% fibre, whereas vacuum infusion gives a final product with 40% resin and 60% fibre content. The strength of the product is greatly dependent on this ratio.
Moulding methods
In general, the reinforcing and matrix materials are combined, compacted and processed to undergo a melding event. After the melding event, the part shape is essentially set, although it can deform under certain process conditions. For a thermoset polymeric matrix material, the melding event is a curing reaction that is initiated by the application of additional heat or chemical reactivity such as an organic peroxide. For a thermoplastic polymeric matrix material, the melding event is a solidification from the melted state. For a metal matrix material such as titanium foil, the melding event is a fusing at high pressure and a temperature near the melt point.
For many molding methods, it is convenient to refer to one mold piece as a "lower" mold and another mold piece as an "upper" mold. Lower and upper refer to the different faces of the molded panel, not the mold's configuration in space. In this convention, there is always a lower mold, and sometimes an upper mold. Part construction begins by applying materials to the lower mold. Lower mold and upper mold are more generalized descriptors than more common and specific terms such as male side, female side, a-side, b-side, tool side, bowl, hat, mandrel, etc. Continuous manufacturing processes use a different nomenclature.
The molded product is often referred to as a panel. For certain geometries and material combinations, it can be referred to as a casting. For certain continuous processes, it can be referred to as a profile. Applied with a pressure roller, a spray device or manually. This process is generally done at ambient temperature and atmospheric pressure. Two variations of open moulding are Hand Layup and Spray-up.
Vacuum bag moulding
A process using a two-sided mould set that shapes both surfaces of the panel. On the lower side is a rigid mould and on the upper side is a flexible membrane or vacuum bag. The flexible membrane can be a reusable silicone material or an extruded polymer film. Then, vacuum is applied to the mould cavity. This process can be performed at either ambient or elevated temperature with ambient atmospheric pressure acting upon the vacuum bag. Most economical way is using a venturi vacuum and air compressor or a vacuum pump.
Pressure bag moulding
This process is related to vacuum bag moulding in exactly the same way as it sounds. A solid female mould is used along with a flexible male mould. The reinforcement is placed inside the female mould with just enough resin to allow the fabric to stick in place. A measured amount of resin is then liberally brushed indiscriminately into the mould and the mould is then clamped to a machine that contains the male flexible mould. The flexible male membrane is then inflated with heated compressed air or possibly steam. The female mould can also be heated. Excess resin is forced out along with trapped air. This process is extensively used in the production of composite helmets due to the lower cost of unskilled labor. Cycle times for a helmet bag moulding machine vary from 20 to 45 minutes, but the finished shells require no further curing if the moulds are heated.
Autoclave moulding
A process using a two-sided mould set that forms both surfaces of the panel. On the lower side is a rigid mold and on the upper side is a flexible membrane made from silicone or an extruded polymer film such as nylon. Reinforcement materials can be placed manually or robotically. They include continuous fiber forms fashioned into textile constructions. Most often, they are pre-impregnated with the resin in the form of prepreg fabrics or unidirectional tapes. In some instances, a resin film is placed upon the lower mold and dry reinforcement is placed above. The upper mold is installed and vacuum is applied to the mold cavity. The assembly is placed into an autoclave. This process is generally performed at both elevated pressure and elevated temperature. The use of elevated pressure facilitates a high fiber volume fraction and low void content for maximum structural efficiency.
Resin transfer moulding (RTM)
A process using a two-sided mould set that forms both surfaces of the panel. The lower side is a rigid mould. The upper side can be a rigid or flexible mould. Flexible moulds can be made from composite materials, silicone or extruded polymer films such as nylon. The two sides fit together to produce a mould cavity. The distinguishing feature of resin transfer moulding is that the reinforcement materials are placed into this cavity and the mould set is closed prior to the introduction of matrix material. Resin transfer moulding includes numerous varieties which differ in the mechanics of how the resin is introduced to the reinforcement in the mould cavity. These variations include everything from vacuum infusion (for resin infusion see also boat building) to vacuum assisted resin transfer moulding (VARTM). This process can be performed at either ambient or elevated temperature.
Other
Other types of molding include press molding, transfer molding, pultrusion molding, filament winding, casting, centrifugal casting and continuous casting. There are also forming capabilities including CNC filament winding, vacuum infusion, wet lay-up, compression molding, and thermoplastic molding, to name a few. The use of curing ovens and paint booths is also needed for some projects.
Tooling
Some types of tooling materials used in the manufacturing of composites structures include invar, steel, aluminum, reinforced silicone rubber, nickel, and carbon fiber. Selection of the tooli
Auto Body Repair in Portland, Salem, Boise, Idaho
One stop auto body shop for car dent repair, auto glass repair, car paint repair, collision repair for any vehicle in Portland, Salem, Boise, Idaho by Kadels Auto Body.
Portland Oregon Auto Body - Courtesy Auto Body
For auto body repair and paint service in Portland Oregon, call Courtesy Auto Body! 8949 SW Canyon Road Portland, Oregon 97225 503-292-4465
East Portland Auto Body : Home
Welcome to East Portland Auto Body where we're ready to handle all of your repair and restoration needs from simple chip repair to total restorations.
Auto Body Repair Shop Portland Downtown Portland ...
Fix Auto Portland Downtown is an expert in car body repair and collision repair for all types of vehicles. Our body shop in Portland guarantees your cars body repair for life.
Auto Body Technology - Portland Oregon Auto Body and ...
Auto Body Technology – Your Complete Auto Body Shop and Collision Repair Facility serving the Portland Oregon Area
Auto Body Repair Shop Portland East Portland, Oregon ...
Description of collision repair services available in Fix Auto's auto body shop centers. -
ACP Auto Body & Towing I 503 255 0060
Quality, Auto Body Repair. ACP AUTO BODY provides high-quality, right price repairs. We can do the job faster than an independent body shop, and at a far less cost than our ...
Auto Body Portland
Get a Collision Repair Estimate Looking for Collision Repair Experts in Portland? Click the auto body shops on the map to see feedback scores, ratings & reviews for your job ...
Auto Body Repair Shops in Portland Oregon
Oregon car crash or Washington auto accident: Insurance links provided by an Oregon car crash lawyer and Washington auto accident lawyer
Lukas Auto Painting & Auto Body Collision Repair in ...
Auto body collision repair and auto painting in Portland, Oregon - with respect and excellence. Lifetime warranty. Eco-Logical. Elder Friendly.