Radiators are used for cooling internal combustion engines, chiefly in automobiles but also in piston-engined aircraft, railway locomotives, motorcycles, stationary generating plant or any similar use of such an engine.
They operate by passing a liquid coolant through the engine block, where it is heated, then through the radiator itself where it loses this heat to the atmosphere. This coolant is usually water-based, but may also be oil. It's usual for the coolant flow to be pumped, also for a fan to blow air through the radiator.
Automobiles
In automobiles with a liquid-cooled internal combustion engine a radiator is connected to channels running through the engine and cylinder head, through which a liquid (coolant) is pumped. This liquid may be water (in climates where water is unlikely to freeze), but is more commonly a mixture of water and antifreeze in proportions appropriate to the climate. Antifreeze itself is usually ethylene glycol or propylene glycol (with a small amount of corrosion inhibitor).
The radiator transfers the heat from the fluid inside to the air outside, thereby cooling the engine. Radiators are also often used to cool automatic transmissions, air conditioners, and sometimes to cool engine oil. Radiators are typically mounted in a position where they receive airflow from the forward movement of the vehicle, such as behind a front grill. Where engines are mid- or rear-mounted, it is common to mount the radiator behind a front grill to achieve sufficient airflow, even though this requires long coolant pipes. Alternatively, the radiator may draw air from the flow over the top of the vehicle or from a side-mounted grill. For long vehicles, such as buses, side airflow is most common for engine and transmission cooling and top airflow most common for air conditioner cooling.
Radiator construction
Automobile radiators are constructed of a pair of header tanks, linked by a core with many narrow passageways, thus a high surface area relative to its volume. This core is usually made of stacked layers of metal sheet, pressed to form channels and soldered or brazed together. For many years radiators were made from brass or copper cores soldered to brass headers. Modern radiators save money and weight by using plastic headers and may use aluminium cores. This construction is less easily repaired than traditional materials.
An earlier construction method was the honeycomb radiator. Round tubes were swaged into hexagons at their ends, then stacked together and soldered. As they only touched at their ends, this formed what became in effect a solid water tank with many air tubes through it.
Vintage cars may also have used radiator cores made from coiled tube, a less-efficient but simpler construction.
Coolant pumps
Radiators first used downward vertical flow, driven solely by a thermosyphon effect. Coolant is heated in the engine, becoming less dense and so rising, cooled, denser coolant in the radiator falling in turn. This effect is sufficient for low-power stationary engines, but inadequate for all but the earliest automobiles. A common fallacy is to assume that a greater vertical separation between engine and radiator can increase the thermosyphon effect. Once the hot and cold headers are separated sufficiently to reach their equilibrium temperatures though, any further separation merely increases pipework length and flow restriction.
All automobiles for many years have used centrifugal pumps to circulate their coolant, driven by geared drives or more commonly by a belt drive. This "fan belt" has a well-established reputation for being slightly unreliable, a failure being rapidly obvious as the engine overheats. Despite the name though, it's the coolant pump's failure that causes the overheating, not the fan.
Heater
A system of valves or baffles, or both, is usually incorporated to simultaneously operate a small radiator inside the car. This small radiator, and the associated blower fan, is called the heater core, and serves to warm the cabin interior. Like the radiator, the heater core acts by removing heat from the engine. For this reason, automotive technicians often advise operators to turn on the heater and set it to high if the engine is overheating.
Temperature control
Waterflow control
The engine temperature is primarily controlled by a wax-pellet type of thermostat, a valve which opens once the engine has reached its optimum operating temperature.
When the engine is cold the thermostat is closed, with a small bypass flow so that the thermostat experiences changes to the coolant temperature as the engine warms up. Coolant is directed by the thermostat to the inlet of the circulating pump and is returned directly to the engine, bypassing the radiator. Directing water to circulate only through the engine allows the temperature to reach optimum operating temperature as quickly as possible whilst avoiding localised "hot spots". Once the coolant reaches the thermostat's activation temperature it opens, allowing water to flow through the radiator to prevent the temperature rising higher.
Once at optimum temperature, the thermostat controls the flow of coolant to the radiator so that the engine continues to operate at optimum temperature. Under peak load conditions, such as labouring slowly up a steep hill whilst heavily laden on a hot day, the thermostat will be approaching fully open because the engine will be producing near to maximum power while the velocity of air flow across the radiator is low. (The velocity of air flow across the radiator has a major effect on its ability to dissipate heat.) Conversely, when cruising fast downhill on a motorway on a cold night on a light throttle, the thermostat will be nearly closed because the engine is producing little power, and the radiator is able to dissipate much more heat than then engine is producing. Allowing too much flow of coolant to the radiator would result in the engine being over cooled and operating at lower than optimum temperature. A side effect of this would be that the passenger compartment heater would not be able to put out enough heat to keep the passengers warm.
The thermostat is therefore constantly moving throughout its range, responding to changes in vehicle operating load, speed and external temperature, to keep the engine at its optimum operating temperature.
Airflow control
Other factors influence the temperature of the engine including radiator size and the type of radiator fan. The size of the radiator (and thus its cooling capacity) is chosen such that it can keep the engine at the design temperature under the most extreme conditions a vehicle is likely to encounter (such as climbing a mountain whilst fully loaded on a hot day).
Airflow speed through a radiator is a major influence on the heat it loses. Vehicle speed affects this, in rough proportion to the engine effort, thus giving crude self-regulatory feedback. Where an additional cooling fan is driven by the engine, this also tracks engine speed similarly.
Engine-driven fans are often regulated by a viscous-drive clutch from the drivebelt, which slips and reduces the fan speed at low temperatures. This improves fuel efficiency by not wasting power on driving the fan unnecessarily. On modern vehicles, further regulation of cooling rate is provided by either variable speed or cycling radiator fans. Electric fans are controlled by a thermostatic switch or the engine control unit. Electric fans also have the advantage of giving good airflow and cooling at low engine revs or when stationary, such as in slow-moving traffic.
Before the development of viscous-drive and electric fans, engines were fitted with simple fixed fans that drew air through the radiator at all times. Vehicles whose design required the installation of a large radiator to cope with heavy work at high temperatures, such as commercial vehicles and tractors would often run cool in cold weather under light loads, even with the presence of a thermostat, as the large radiator and fixed fan caused a rapid and significant drop in coolant temperature as soon as the thermostat opened. This problem could be solved by fitting a radiator blind to the radiator which could be adjusted to partially or fully block the airflow. At its simplest the blind was a roll of material (such as canvas or rubber that was unfurled along the length of the radiator to cover the desired portion. Some vehicles had a series of shutters that could be adjusted from the driver's seat to provide a very fine degree of control.
...
CBM Radiators - Plate Oil Coolers (Brazed)
Oil Coolers; Bar & Plate; Plate Oil Coolers (Brazed) Fan Control Systems; Pre Coolers ... Plate Oil Coolers (Brazed) Compact, robust, efficient - Manufactured entirely ...
Oil Coolers
Thermatic Fans; Controller & Switches; Fan Clutches; Transmission Coolers; TyreGuard (TPMS) ... Transmission Oil Coolers Because of the tremendous heat generated in an ...
Hayden - Transmission and Engine Oil Coolers
Fan and cooler preassembled ; Remote mounting ; Stator fan blade technology Power Steering Oil Cooler. Our power steering oil cooler removes destructive heat generated within a power ...
Oil Cooler and Filtration Accessories by US Motor Works
Engine: >Oil Coolers >Cooler & Filtration Access. >Fan Mounted Oil Coolers >Combination Coolers >Power Steering Coolers. Fans: >Electric Cooling Fans
FLUIDYNE - High Performance - Radiators and Oil Coolers
-- DIRECT FIT PRODUCTS --[ Domestics] [ Imports] [ Exotics] [ Universal Radiators] [ Supercharger Cooler-Coolers] [ Oil Coolers & Fans] [To Find A Dealer Near You, Click Here!
Oil Coolers & Fans
Improve & extend the life of your transmission. To improve and extend the life of your transmission, a transmission oil cooler is a key ingredient.
Oil Coolers
JEGS HD Engine Oil Cooler JEGS NPT to Hose Fittings & Hose JEGS Universal Electric Fan, Oil & Transmission Cooler Mount Kit
Porsche Oil Cooler Fan: Engine Cooling & Oil Cooler ...
Oil Cooler Fan. Porsche Oil Cooler Fan: Engine Cooling & Oil Cooler Related Parts. Porsche Oil Cooler Fan Aftermarket.
ELEPHANT RACING Oil Cooler Fans
Home >911 Oil Cooling >Oil Cooler Fans. Oil Cooler Fans. Low speed cooling enhancement Oil coolers only work when air is flowing ...